Camluxy LED Flash Induction Lamp Wireless Doorbell PIR Motion Sensing Light 38 Songs Waterproof Intelligent Door Bell Chime Kit Product Introduction ● This product integrates wireless doorbell and induction light, and can be used for two purposes. ● High baud rate RF technology, intelligent MCU sleep wakeup, with high-capacity alkaline battery, longer standby time. ● The receiver is battery powered, which breaks the limit and can be placed at will. It is suitable for more occasions. ● 38 music, 4-level volume adjustment, with mute mode. ● Millions of group codes are not repetitive and can be freely combined to achieve dual control, mutual control and multiple control. ● The induction lamp uses infrared body sensing+light sensing technology, and it will light up for 30 seconds when someone passes by at night. ● Three working modes: AUTO mode/OFF mode/ON mode. ● The transmitter adopts high-performance battery, which is super power-saving, easy to paste and install. 3 Lighting Modes For Different Needs OFF|Turn Light Off AUTO|Motion Sensor Light ON|Always-ON Lighting Match As Needed Set different ringing tones to distinguish which door the visiting guests are at. At the same time, the receiver can also set different volume modes to apply to different scenes. Signal Receiving Range:250M (In An Open Environment) Human body night light 120° Sensing distance 3-5m About one minute after the man left(Automatic light off) People walk in the sensing zone(Automatic continuous light) People are out of range(Light off IP68 Waterproof Super long service life,slow energy consumption,green environmental protection and installation. * Remote control distance varies in different environments. * Use time is determined by the use frequency and battery quality. * The sensing distance angle is related to the temperature environment and varies under different environments. * The sensor is only for indoor use, and the outdoor use is easy to misoperation due to the influence of wind direction and temperature. Music Adjustment : Press the music key to switch to the nextmusic, a total of 38 music . Volume Adjustment : Press the volume key, the volume from high to low is 4-3-2-1-0, and 0 is silent mode (only flickering without sound in silent mode) Reset Function : Long press the music key for 3 seconds to reset to the first music and maximum volume. Normal Pairing Mode : Press the volume key and music key at the same time, the receiver will sound "Di", enter the pairing mode, and then press the transmitter, the receiver will sound "Ding Dong", indicating that the pairing is successful. Later, you can press the music key to switch music. If pairing fails within 5 seconds, the receiver will exit pairing mode after sending "didi" twice. Independent Pairing Mode : After the receiver selects the favorite music, long press the volume key for 3 seconds, the host sends out "Di" sound to enter the pairing mode, and then press transmitter 1, the host sends out "Ding Dong" sound, and the pairing is successful. Press transmitter 1 later and the receiver will send the previously selected music. If pairing fails within 5 seconds, the receiver will exit pairing mode after sending "didi" twice. As described above, another music is selected and paired with transmitter 2. If different transmitters are installed on the front door and rear door respectively, the host will send different music after receiving the signal. If the corresponding transmitter needs to change music, please reselect the music and pair it again. Each receiver can be paired with up to 15 transmitters. AUTO mode: In the dark environment, when someone passes through the induction range, the light will automatically light up. When the person leaves the induction range, the light will go out 30 seconds later OFF mode: LED off mode. ON mode: Normally on mode. (Please pay attention to saving electricity in this mode) Low battery reminder: When the battery is low, the LED will flash to remind you to replace the battery. Type-C interface: Recommended for use when the battery is out of power or used at high frequency (non charging port). Matters Needing Attention ● After the battery is used up, please replace it in time, otherwise the battery is easy to leak and corrode the machine. ● Please use alkaline battery instead of carbon battery for the receiver. ● Do not use rechargeable batteries for the receiver. ● Do not mix the old and new batteries of the receiver. ● In order to ensure the sensing effect, please install the receiver at a suitable height and an unobstructed position. ● This product is only for indoor use, and can be triggered by air flow when used outdoors. ● Do not install it opposite the night vision camera. (The infrared ray of the camera will interfere with this product) ● Do not use this product in high temperature and humid environment. ● Keep away from water source and heat source to avoid damaging the product and causing potential safety hazards. ● Protect the environment and respect the law. Please dispose of waste batteries properly.
